SIMPLE SOLUTIONS

AX25IPD.CONF(5) - man page online | file formats

Control the operation of ax25ipd.

Chapter
7 July 1997
AX25IPD.CONF(5)                     Linux Programmer's Manual                     AX25IPD.CONF(5)

NAME ax25ipd.conf - Control the operation of ax25ipd.
DESCRIPTION The ax25ipd.conf file controls the operation of the ax25ipd(8) program. The operation of the config file can best be seen in an example: # # ax25ipd configuration file for station floyd.vk5xxx.ampr.org # # Select axip transport. 'ip' is what you want for compatibility # with most other gates ... # socket ip # # Set ax25ipd mode of operation. (digi or tnc) # mode tnc # # If you selected digi, you must define a callsign. If you selected # tnc mode, the callsign is currently optional, but this may change # in the future! (2 calls if using dual port kiss) # # mycall vk5xxx-4 # mycall2 vk5xxx-5 # # In digi mode, you may use an alias. (2 for dual port) # # myalias svwdns # myalias2 svwdn2 # # Send an ident every 540 seconds ... # # beacon after 540 # btext ax25ip -- tncmode rob/vk5xxx -- Experimental AXIP gateway # # Serial port, ethertap interface, or pipe connected to a kissattach in my case # alternatively, if you have the kernel module bpqether: # if you use tun/tap or ethertap instead of kissattach you may say, without # leading slashes (!! - that's how ax25ipd consideres using the tty kiss # driver or tun/tap or ethertap): # with tun/tap: # device foobar # with ethertap (obsolete): # device tap0 # make sure you set a mycall above, or say axparms foobar -setcall te1st # note: the device will be up when you assign an ip address # _after_ starting ax25rtd (which initializes the device), start ax25d # with bpqether or pty, you do not need to care about the speed # tun/tap: as descriped in /usr/src/linux/Documentatioa/networking/tuntap.txt, # make a device # like this: # crw-r--r-- 1 root root 10, 200 Nov 26 13:32 tun # with the command mknod /dev/net/tun c 10 200 # As serial port, you could assign physical ports like ttyS0 or ptys. # ax25ipd supports BSD-style pseudo-terminals as well as the Unix98 pty's. # If the tty argument is "/dev/ptmx", then Unix98 behaviour # will automatically take effect. With Unix98 pty's, the slave tty name # could not be forseen. That's why ax25ipd will print the corresponding # slave pty name as a separate line on stdout. # #device ampr device /dev/ttyp0 # # Set the device speed # speed 9600 # # loglevel 0 - no output # loglevel 1 - config info only # loglevel 2 - major events and errors # loglevel 3 - major events, errors, and AX25 frame trace # loglevel 4 - all events # log 0 for the moment, syslog not working yet ... # loglevel 4 # # If we are in digi mode, we might have a real tnc here, so use param to # set the tnc parameters ... # # param 1 20 # # Broadcast Address definition. Any of the addresses listed will be forwarded # to any of the routes flagged as broadcast capable routes. # broadcast QST-0 NODES-0 # # ax.25 route definition, define as many as you need. # format is route (call/wildcard) (ip host at destination) # ssid of 0 routes all ssid's # # route <destcall> <destaddr> [flags] # # Valid flags are: # b - allow broadcasts to be transmitted via this route # d - this route is the default route # route vk2sut-0 44.136.8.68 b route vk5asf 44.136.188.221 b route vk2abc 44.1.1.1 d # # More to come ...
FILES /etc/ax25/ax25ipd.conf
SEE ALSO ax25ipd(8).
Linux 7 July 1997 AX25IPD.CONF(5)
This manual Reference Other manuals
ax25ipd.conf(5) referred by ax25ipd(8)
refer to ax25ipd(8)