GROSSD.CONF(5) - Linux man page online | File formats

Greylisting of Suspicious Sources daemon configuration file.

grossd(5) grossd(5)


grossd.conf - Greylisting of Suspicious Sources daemon configuration file




grossd(8) reads configuration data from /etc/grossd.conf (or the file specified with -f on the command line). An example configuration file is installed by default. You have to set some configuration options in order to get grossd(8) running in your environment. The format is as follows: name = value [ ; param ] ... Not all options accept parameters - refer to individual descriptions. The comment separator is `#', everything after it is ignored by the config file parser. Network configuration options host is the address the server should listen for queries. Default is `localhost'. port is the port the server should listen for queries. Default is 5525. sync_listen is the address to listen for communication with the peer. It defaults to the host setting. sync_peer is the address of the peer used when running in clustered mode. sync_port is the tcp port number to listen to and connect to in communication with the peer. Default is 5524. status_host is the address grossd(8) listens for status queries. Default is `localhost'. status_port is the port number grossd(8) listens for status queries. Default is 5522. protocol activates the server protocols grossd(8) will support. Valid settings are `sjsms', `postfix' and `milter'. milter_listen is the socket address for the Milter service. The format is `proto:port@host'. Refer to Milter documentation for the specifics. Core server options You can probably leave the default values for these settings. If your daily mail flow exceeds millions of messages per day you may want to tweak query_timelimit and/or pool_maxthreads. If you run grossd(8) in a server with limited memory you may want to adjust filter_bits. filter_bits is the size of the Bloom filter. The size will be 2^filter_bits. Lowering this value will increase the probability of false matches in each individual filter. Default is 24. number_buffers is the number of Bloom filters used in the ring queue. Raising this value will cause an entry to stay in the server's memory longer. Default is 8. rotate_interval is the number of seconds between Bloom filter rotations. Let N := number_buffers and I := rotate_interval. An entry will stay in the server's memory for N - 0.5 * I seconds on average. Defaults to 3600 seconds (one hour). update is the way server updates the database. Valid options are `grey' and `always'. If set to `grey', which is the default, grossd(8) will update the database only if the response is `STATUS_GREY'. Setting it to `always' may reduce the impact on DNS servers. grey_mask is the mask for grossd(8) to use when matching the `smtp-client-ip' against the database. Default is 24, which makes grossd(8) to treat addresses like a.b.c.d as a.b.c.0. Setting grey_mask to 32 makes grossd(8) to require that consecutive attempts are made from the same `smtp-client-ip'. statefile is the full path of the file that the server uses to store the state information. Default is not to have a statefile. You may want to configure a statefile especially if you do not configure replication. pidfile is the full path of the file grossd(8) writes its pid into. You can set parameter `check', if you want to keep grossd(8) from starting should pidfile already exist. Query constraints grey_delay is the time in seconds new triplets are kept on the greylist. Default is 180. query_timelimit is the query timeout in milliseconds. You may have to adjust this if you exceed millions of queries a day. pool_maxthreads is the maximum threadcount per pool. You may have to raise the limit from the default if you get more than 100 queries per second and/or have slow DNS servers. The rule of thumb is to decide how many queries you want grossd(8) to be able to handle per second, and multiply that with query_timelimit (in seconds, of course). It defaults to 100. Configuring server responses block_threshold is the threshold after which grossd(8) sends a permanent error to the client. Every check that considers `smtp-client-ip' as suspicious returns a value (check weight). When sum of these values gets equivalent or greater than block_threshold grossd(8) sends a STATUS_BLOCK response. Default is 0 which disables this functionality. block_reason is the reason given when client is too suspicious, see block_threshold. Default is “Bad reputation”. grey_threshold is analogous to block_threshold, except at the threshold grossd(8) sends a STATUS_GREY response. Default is 1. If set to 0 grossd(8) will greylist by default. This makes it possible to combine a traditional greylister and rbl checks. grey_reason is the reason given when client is suspicious enough to be greylisted, see grey_threshold. Default is “Please try again later.”. Logging options log_method is used to choose the logging method. Currently the only implemented method is `syslog', which is the default. log_level sets the logging verbosity. Possible values in the order of increasing verbosity are `error', `warning', `notice', `info' and `debug'. log_level defaults to `info'. syslog_facility is the facility syslog sends log messages with. It defaults to `mail'. stat_type is the name of the requested statistic. It is of multivalued type. The valid options are: `full' log all possible statistics, `none' no statistics logging, `status' basic set of statistics, `since_startup' basic set since the startup and `delay' log processing delay statistics. Default is `none'. Setting both `none' and `full' is undefined. stat_interval is the number of seconds between status log entries. Default is 3600. Configuring checks check is a multivalued option, that is, you can configure multiple checks by setting check option multiple times. Currently implemented checks are `dnsbl', `dnswl', `rhsbl' and `blocker'. Refer to sections describing the checks below. If you don't configure any checks grossd(8) will act as a traditional greylisting server. dnsbl is a DNS domain name of the dnsbl that `dnsbl' check will query. There are no defaults, but the default configuration file lists a few as an example. If you have any locally administered block lists then you should be aware that grossd(8) makes all queries as fully qualified. You may assign different weights for the dnsbls, default weight is 1. Refer to grey_threshold and block_threshold about the weights. dnsbl is a multivalued option. dnswl is analogous to dnsbl. Remember that dnswl is a definitive check, that is grossd(8) waits for the check to complete before deciding how to respond. This may cause unwanted latency, although you can adjust the maximum latency by query_timelimit option. dnswl is highly recommended if you use grossd(8) as a traditional greylister. This is a multivalued option. rhsbl is analogous to dnsbl, but the check is made with the right hand side of the sender address (the email domain) instead of the IP address. This is a multivalued option. blocker_host is the host name of the Sophos blocker server. This is used only if check = `blocker' is set. blocker_port is the TCP port of the Sophos blocker service. Default is 4466. blocker_weight is the weight of the blocker check. See description of grey_threshold and block_threshold regarding the weights. Sun Java System Messaging Server specific options You may configure the responses grossd(8) sends over to grosscheck library. sjsms_response_grey is the mapping result template grossd(8) uses for a STATUS_GREY result. Default is `$X4.4.3|$N%reason%', where `%reason%' is the template for the reason string. sjsms_response_match is the mapping result template grossd(8) uses for a STATUS_MATCH result. Default is `$Y'. sjsms_response_trust is the mapping result template grossd(8) uses for a STATUS_TRUST result. Default is `$Y'. sjsms_response_block is the mapping result template grossd(8) uses for a STATUS_BLOCK result. Default is `$N%reason%', where `%reason%' is the template for the reason string. Postfix specific options postfix_response_grey is the response template grossd(8) uses for a STATUS_GREY result. Default is `action=defer_if_permit %reason%', where `%reason' is the template for the reason string. postfix_response_block is the response template grossd(8) uses for a STATUS_BLOCK result. Default is `action=reject %reason%', where `%reason' is the template for the reason string.


Sun Java System Messaging Server You have to add a mapping entry to set SJSMS to query grossd(8). It's also a good idea to exclude postmaster and abuse addresses before querying grossd(8). Here is an example: ORIG_MAIL_ACCESS ! allow all DSNs and MDNs TCP|*|*|*|*|*|*|tcp_local||*|* $Y$E ! allow all incoming mail to postmaster and abuse TCP|*|*|*|*|*|*|tcp_local|*|*|postmaster@* $Y$E TCP|*|*|*|*|*|*|tcp_local|*|*|abuse@* $Y$E ! use gross to check all triplets (client_ip,sender,recipient) TCP|*|*|*|*|SMTP/*|*|tcp_local|*|*|* $[/usr/lib/i386-linux- gnu/,grosscheck,,,5525,$2,$=$8$_,$=$6$_,$=$4$_] Mapping call parameters are as follows: 1. full path of the 2. function name to call (always grosscheck) 3. first server's IP address, 4. second server's IP address, 5. UDP port for server connections, 6. SMTP client's IP address, 7. envelope sender's email address, 8. envelope recipient's email address, 9. HELO/EHLO string. Postfix Grossd implements native Postfix policy delegation protocol. Just specify grossd server address at the `smtpd_recipient_restrictions' in the main configuration file : /etc/postfix/ smtpd_recipient_restrictions = ... reject_unauth_destination check_policy_service inet:host:port ... Refer to Postfix documentation at <> for specifics. Exim Exim can be configured to query grossd(8) via Postfix policy delegation protocol. Main section: GROSS_QUERY = sender=$sender_address\\n\\ recipient=$local_part@$domain\\n\\ client_address=$sender_host_address\\n\\ grossd_mode=single\\n\\n Acl section: # gross warn set acl_c0 = ${readsocket{inet:}{GROSS_QUERY}} defer message = Please try again later. condition = ${if match {$acl_c0}{action=defer_if_permit}} deny message = ${if match {$acl_c0}{action=reject (.*)}{$1}\\ {Rejected by Gross.}} condition = ${if match {$acl_c0}{action=reject}} Sendmail Sendmail can query grossd via milter protocol. Insert this in and configure milter_listen accordingly: INPUT_MAIL_FILTER(`Gross', `S=inet:5523@localhost, T=R:20s') You can check if your version of Sendmail has Milter support compiled in by issuing the following command: sendmail -bt -d0.1


grossd(8) Gross project site: <> Bloom filters: <>


Eino Tuominen and Antti Siira
2008-05-04 grossd(5)
This manual Reference Other manuals
grossd.conf(5) referred by grossd(8)
refer to grossd(8)
Download raw manual
Index № 5 (+2141)
Go top