SIMPLE SOLUTIONS

IGMPPROXY.CONF(5) - Linux man page online | File formats

Configuration file for igmpproxy(8) multicast daemon.

Chapter
igmpproxy.conf(5) File Formats Manual igmpproxy.conf(5)

NAME

igmpproxy.conf - Configuration file for igmpproxy(8) multicast daemon

DESCRIPTION

igmpproxy.conf contains the configuration for the igmpproxy multicast daemon. It defines which network interfaces should be used by the routing daemon. Each interface must be give one of the following roles: upstream , downstream or disabled The upstream network interface is the outgoing interface which is responsible for communi‐ cating to available multicast data sources. There can only be one upstream interface. Downstream network interfaces are the distribution interfaces to the destination networks, where multicast clients can join groups and receive multicast data. One or more downstream interfaces must be configured. On disabled network interfaces all IGMP or multicast traffic is ignored altogether. If multiple IP addresses is used on one single interface (ae. eth0:1 ...), all interface aliases not in use should be configured as disabled. Any line in the configuration file starting with # is treated as a comment. Keywords and parameters can be distributed over many lines. The configuration file has two main key‐ words: quickleave Enables quickleave mode. In this mode the daemon will send a Leave IGMP message upstream as soon as it receives a Leave message for any downstream interface. The daemon will then ask for Membership reports on the downstream interfaces, and if a report is received the group is joined again upstream. Normally this is not noticed at all by clients on the downstream networks. If it's vital that the daemon should act exactly as a real multicast client on the upstream interface, this function should not be used. Disabling this function increases the risk of bandwidth satura‐ tion. phyint interface role [ ratelimit limit ] [ threshold ttl ] [ altnet networkaddr ... ] Defines the state and settings of a network interface.

PHYINT OPTIONS

interface The name of the interface the settings are for. This option is required for phyint settings. role The role of the interface. This should be either upstream (only one interface), downstream (one or more interfaces) or disabled . This option is required. ratelimit limit Defines a ratelimit for the network interface. If ratelimit is set to 0 (default), no ratelimit will be applied. This setting is optional. threshold ttl Defines the TTL threshold for the network interface. Packets with a lower TTL than the threshols value will be ignored. This setting is optional, and by default the threshold is 1. altnet networkaddr ... Defines alternate sources for multicasting and IGMP data. The network address must be on the following format 'a.b.c.d/n'. By default the router will accept data from sources on the same network as configured on an interface. If the multicast source lies on a remote network, one must define from where traffic should be accepted. This is especially useful for the upstream interface, since the source for multi‐ cast traffic is often from a remote location. Any number of altnet parameters can be specified. whitelist networkaddr Defines a whitelist for multicast groups. The network address must be in the fol‐ lowing format 'a.b.c.d/n'. If you want to allow one single group use a network mask of /32, i.e. 'a.b.c.d/32'. By default all multicast groups are allowed on any downstream interface. If at least one whitelist entry is defined, all igmp membership reports for not explic‐ itly whitelisted multicast groups will be ignored and therefore not be served by igmpproxy. This is especially useful, if your provider does only allow a predefined set of multicast groups. These whitelists are only obeyed by igmpproxy itself, they won't prevent any other igmp client running on the same machine as igmpproxy from requesting 'unallowed' multicast groups. You may specify as many whitelist entries as needed. Although you should keep it as simple as possible, as this list is parsed for every membership report and there‐ fore this increases igmp response times. Often used or large groups should be defined first, as parsing ends as soon as a group matches an entry. You may also specify whitelist entries for the upstream interface. Only igmp mem‐ bership reports for explicitly whitelisted multicast groups will be sent out on the upstream interface. This is useful if you want to use multicast groups only between your downstream interfaces, like SSDP from a UPnP server.

EXAMPLE

## Enable quickleave quickleave ## Define settings for eth0 (upstream) phyint eth0 upstream altnet 10.0.0.0/8 ## Disable alternate IP on eth0 (eth0:0) phyint eth0:0 disabled ## Define settings for eth1 (downstream) phyint eth1 downstream ratelimit 0 threshold 1 ## Define settings for eth2 (also downstream) phyint eth2 downstream

SEE ALSO

igmpproxy(8)

AUTHOR

Originally written by Johnny Egeland <@rlo.org>
igmpproxy 0.2.1 igmpproxy.conf(5)
This manual Reference Other manuals
igmpproxy.conf(5) referred by igmpproxy(8)
refer to igmpproxy(8)
Download raw manual
Main page File Formats Manual (+542) igmpproxy 0.2.1 (+2) № 5 (+2141)
Go top