UDPLITE(7) - man page online | overview, conventions, and miscellany
Lightweight User Datagram Protocol.
UDPLITE(7) Linux Programmer's Manual UDPLITE(7)
NAME udplite - Lightweight User Datagram Protocol SYNOPSIS #include <sys/socket.h> sockfd = socket(AF_INET, SOCK_DGRAM, IPPROTO_UDPLITE); DESCRIPTION This is an implementation of the Lightweight User Datagram Protocol (UDP-Lite), as described in RFC 3828. UDP-Lite is an extension of UDP (RFC 768) to support variable-length checksums. This has advantages for some types of multimedia transport that may be able to make use of slightly damaged datagrams, rather than having them discarded by lower-layer protocols. The variable-length checksum coverage is set via a setsockopt(2) option. If this option is not set, the only difference to UDP is in using a different IP protocol identifier (IANA number 136). The UDP-Lite implementation is a full extension of udp(7)—that is, it shares the same API and API behavior, and in addition offers two socket options to control the checksum cover‐ age. Address format UDP-Litev4 uses the sockaddr_in address format described in ip(7). UDP-Litev6 uses the sockaddr_in6 address format described in ipv6(7). Socket options To set or get a UDP-Lite socket option, call getsockopt(2) to read or setsockopt(2) to write the option with the option level argument set to IPPROTO_UDPLITE. In addition, all IPPROTO_UDP socket options are valid on a UDP-Lite socket. See udp(7) for more informa‐ tion. The following two options are specific to UDP-Lite. UDPLITE_SEND_CSCOV This option sets the sender checksum coverage and takes an int as argument, with a checksum coverage value in the range 0..2^16-1. A value of 0 means that the entire datagram is always covered. Values from 1-7 are illegal (RFC 3828, 3.1) and are rounded up to the minimum coverage of 8. With regard to IPv6 jumbograms (RFC 2675), the UDP-Litev6 checksum coverage is lim‐ ited to the first 2^16-1 octets, as per RFC 3828, 3.5. Higher values are therefore silently truncated to 2^16-1. If in doubt, the current coverage value can always be queried using getsockopt(2). UDPLITE_RECV_CSCOV This is the receiver-side analogue and uses the same argument format and value range as UDPLITE_SEND_CSCOV. This option is not required to enable traffic with partial checksum coverage. Its function is that of a traffic filter: when enabled, it instructs the kernel to drop all packets which have a coverage less than the specified coverage value. When the value of UDPLITE_RECV_CSCOV exceeds the actual packet coverage, incoming packets are silently dropped, but may generate a warning message in the system log. ERRORS All errors documented for udp(7) may be returned. UDP-Lite does not add further errors. FILES /proc/net/snmp - basic UDP-Litev4 statistics counters. /proc/net/snmp6 - basic UDP-Litev6 statistics counters. VERSIONS UDP-Litev4/v6 first appeared in Linux 2.6.20. BUGS Where glibc support is missing, the following definitions are needed: #define IPPROTO_UDPLITE 136 #define UDPLITE_SEND_CSCOV 10 #define UDPLITE_RECV_CSCOV 11 SEE ALSO ip(7), ipv6(7), socket(7), udp(7) RFC 3828 for the Lightweight User Datagram Protocol (UDP-Lite). Documentation/networking/udplite.txt in the Linux kernel source tree COLOPHON This page is part of release 4.04 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at http://www.kernel.org/doc/man-pages/.Linux 2014-07-08 UDPLITE(7)
|This manual||Reference||Other manuals|
|refer to||getsockopt(2) | ip(7) | ipv6(7) | socket(7) | udp(7)|