SIMPLE SOLUTIONS

GPIOIIC(4FREEBSD) - man page online | special files

GPIO I2C bit-banging device driver.

Chapter
May 14, 2014
GPIOIIC(4)                         BSD Kernel Interfaces Manual                        GPIOIIC(4)

NAME

gpioiic — GPIO I2C bit-banging device driver

SYNOPSIS

device gpio device gpioiic device iic device iicbb device iicbus

DESCRIPTION

The gpioiic driver provides an IIC bit-banging interface using two GPIO pins for the SCL and SDA on the gpiobus. gpioiic implements an open colector kind of output, as recommended by the standard, when driving the pins on the gpiobus, i.e, they are never switched to the log‐ ical value of '1', or they are '0' or simply open (Hi-Z/tri-state). So the pullup resistors are required so gpioiic can work. On a hint based system, like MIPS, these values are configureable for the gpioiic: hint.gpioiic.%d.at The gpiobus you are attaching to. Normally just gpiobus0. hint.gpioiic.%d.pins This is a bitmask of the pins on the gpiobus that are to be used for SCLOCK and SDATA from the GPIO IIC bit-banging bus. To configure pin 0 and 7, use the bitmask of 0b10000001 and convert it to a hexadeci‐ mal value of 0x0081. Please note that this mask should only ever have two bits set (any others bits - i.e., pins - will be ignored). hint.gpioiic.%d.scl Indicates which bit in the hint.gpioiic.%d.pins should be used as the SCLOCK source. Optional, defaults to 0. hint.gpioiic.%d.sda Indicates which bit in the hint.gpioiic.%d.pins should be used as the SDATA source. Optional, defaults to 1. On a FDT(4) based system, like ARM, the dts part for a gpioiic device usually looks like: gpio: gpio { gpio-controller; ... gpioiic0 { compatible = "gpioiic"; /* * Attach to GPIO pins 21 and 22. Set them * initially as inputs. */ gpios = <&gpio 21 1 0 &gpio 22 1 0>; scl = <0>; /* GPIO pin 21 - optional */ sda = <1>; /* GPIO pin 22 - optional */ /* This is an example of a gpioiic child. */ gpioiic-child0 { compatible = "lm75"; i2c-address = <0x4f>; }; }; }; Where: compatible Should always be set to "gpioiic". gpios The gpios property indicates which GPIO pins should be used for SCLOCK and SDATA on the GPIO IIC bit-banging bus. For more details about the gpios property, please consult /usr/src/sys/boot/fdt/dts/bindings-gpio.txt. scl The scl option indicates which bit in the gpios should be used as the SCLOCK source. Optional, defaults to 0. sda The sda option indicates which bit in the gpios should be used as the SDATA source. Optional, defaults to 1.

SEE ALSO

fdt(4), gpio(4), gpioled(4), iic(4), iicbb(4), iicbus(4)

HISTORY

The gpioiic manual page first appeared in FreeBSD 10.1.

AUTHORS

This manual page was written by Luiz Otavio O Souza.
BSD May 14, 2014 BSD
This manual Reference Other manuals
gpioiic(4freebsd) referred by gpio(4freebsd) | gpiobus(4freebsd) | gpioled(4freebsd)
refer to gpio(4freebsd) | gpioled(4freebsd) | iic(4freebsd) | iicbb(4freebsd) | iicbus(4freebsd)