CLVMD(8) - Linux man page online | Administration and privileged commands
Cluster LVM daemon.
LVM TOOLS 2.02.176(2) (2017-11-03)
CLVMD(8) System Manager's Manual CLVMD(8)
Red Hat Inc LVM TOOLS 2.02.176(2) (2017-11-03) CLVMD(8)
NAMEclvmd — cluster LVM daemon
SYNOPSISclvmd [-C] [-d [value]] [-E lock_uuid] [-f] [-h] [-I cluster_manager] [-R] [-S] [-t time‐ out] [-T start_timeout] [-V]
DESCRIPTIONclvmd is the daemon that distributes LVM metadata updates around a cluster. It must be running on all nodes in the cluster and will give an error if a node in the cluster does not have this daemon running. Also see lvmlockd(8) for a newer method of using LVM on shared storage.
OPTIONS-C Only valid if -d is also specified. Tells all clvmds in a cluster to enable/dis‐ able debug logging. Without this switch, only the local clvmd will change its debug level to that given with -d. This does not work correctly if specified on the command-line that starts clvmd. If you want to start clvmd and enable cluster-wide logging then the command needs to be issued twice, eg: clvmd clvmd -d2 -d [value] Set debug logging level. If -d is specified without a value then 1 is assumed. Value can be: 0 — Disabled 1 — Sends debug logs to stderr (implies -f) 2 — Sends debug logs to syslog(3) -E lock_uuid Pass lock uuid to be reacquired exclusively when clvmd is restarted. -f Don't fork, run in the foreground. -h Show help information. -I cluster_manager Selects the cluster manager to use for locking and internal communications. As it is quite possible to have multiple managers available on the same system you might have to manually specify this option to override the search. By default, omit -I is equivalent to -Iauto. Clvmd will use the first cluster man‐ ager that succeeds, and it checks them in a predefined order cman, corosync, ope‐ nais. The available managers will be listed by order as part of the clvmd -h out‐ put. -R Tells all the running instance of clvmd in the cluster to reload their device cache and re-read the lvm configuration file lvm.conf(5). This command should be run whenever the devices on a cluster system are changed. -S Tells the running clvmd to exit and reexecute itself, for example at the end of a package upgrade. The new instance is instructed to reacquire any locks in the same state as they were previously held. (Alternative methods of restarting the daemon have the side effect of changing exclusive LV locks into shared locks.) -t timeout Specifies the timeout for commands to run around the cluster. This should not be so small that commands with many disk updates to do will fail, so you may need to increase this on systems with very large disk farms. The default is 60 seconds. -T start_timeout Specifies the start timeout for clvmd daemon startup. If the daemon does not report that it has started up within this time then the parent command will exit with sta‐ tus of 5. This does NOT mean that clvmd has not started! What it means is that the startup has been delayed for some reason; the most likely cause of this is an inquorate cluster though it could be due to locking latencies on a cluster with large numbers of logical volumes. If you get the return code of 5 it is usually not necessary to restart clvmd it will start as soon as that blockage has cleared. This flag is to allow startup scripts to exit in a timely fashion even if the clus‐ ter is stalled for some reason. The default is 0 (no timeout) and the value is in seconds. Don't set this too small or you will experience spurious errors. 10 or 20 seconds might be sensible. This timeout will be ignored if you start clvmd with the -d. -V Display the version of the cluster LVM daemon.
NOTESActivation In a clustered VG, clvmd is used for activation, and the following values are possible with lvchange/vgchange -a: y|sy clvmd activates the LV in shared mode (with a shared lock), allowing multiple nodes to activate the LV concurrently. If the LV type prohibits shared access, such as an LV with a snapshot, an exclusive lock is automatically used instead. clvmd attempts to activate the LV concurrently on all nodes. ey clvmd activates the LV in exclusive mode (with an exclusive lock), allowing a sin‐ gle node to activate the LV. clvmd attempts to activate the LV concurrently on all nodes, but only one will succeed. ly clvmd attempts to activate the LV only on the local node. If the LV type allows concurrent access, then shared mode is used, otherwise exclusive. n clvmd attempts to deactivate the LV on all nodes. ln clvmd attempts to deactivate the LV on the local node.
ENVIRONMENT VARIABLESLVM_CLVMD_BINARY The CLVMD binary to use when clvmd restart is requested. Defaults to /clvmd. LVM_BINARY The LVM2 binary to use. Defaults to /lvm.
SEE ALSOsyslog(3), lvm.conf(5), lvm(8), lvmlockd(8), lvmsystemid(7)
|This manual||Reference||Other manuals|
cmirrord(8) | lvchange(8) | lvconvert(8) | lvcreate(8) | lvdisplay(8) | lvextend(8) | lvm(8) | lvm-fullreport(8) | lvm-lvpoll(8) | lvmconfig(8) | lvmdiskscan(8) | lvreduce(8) | lvremove(8) | lvrename(8) | lvresize(8) | lvs(8) | lvscan(8) | pvchange(8) | pvck(8) | pvcreate(8)
|refer to||lvm(8) | lvm.conf(5) | lvmlockd(8) | lvmsystemid(7) | syslog(3)|