USB(4FREEBSD) - man page online | special files
Universal Serial Bus.
November 26, 2013
USB(4) BSD Kernel Interfaces Manual USB(4)
NAMEusb — Universal Serial Bus
SYNOPSISTo compile this driver into the kernel, place the following line in your kernel configura‐ tion file: device usb Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): usb_load="YES"
USERLAND PROGRAMMINGUSB functions can be accessed from userland through the libusb library. See libusb(3) for more information.
DESCRIPTIONFreeBSD provides machine-independent bus support and drivers for USB devices in host and device side mode. The usb driver has three layers: USB Controller (Bus) USB Device USB Driver The controller attaches to a physical bus like pci(4). The USB bus attaches to the con‐ troller, and the root hub attaches to the controller. Any devices attached to the bus will attach to the root hub or another hub attached to the USB bus. The uhub device will always be present as it is needed for the root hub.
INTRODUCTION TO USBThe USB is a system where external devices can be connected to a PC. The most common USB speeds are: Low Speed (1.5MBit/sec) Full Speed (12MBit/sec) High Speed (480MBit/sec) Each USB has a USB controller that is the master of the bus. The physical communication is simplex which means the host controller only communicates with one USB device at a time. There can be up to 127 devices connected to an USB HUB tree. The addresses are assigned dynamically by the host when each device is attached to the bus. Within each device there can be up to 16 endpoints. Each endpoint is individually addressed and the addresses are static. Each of these endpoints will communicate in one of four dif‐ ferent modes: control, isochronous, bulk, or interrupt. A device always has at least one endpoint. This endpoint has address 0 and is a control endpoint and is used to give com‐ mands to and extract basic data, such as descriptors, from the device. Each endpoint, except the control endpoint, is unidirectional. The endpoints in a device are grouped into interfaces. An interface is a logical unit within a device; e.g. a compound device with both a keyboard and a trackball would present one interface for each. An interface can sometimes be set into different modes, called alternate settings, which affects how it operates. Different alternate settings can have different endpoints within it. A device may operate in different configurations. Depending on the configuration, the device may present different sets of endpoints and interfaces. The bus enumeration of the USB bus proceeds in several steps: 1. Any interface specific driver can attach to the device. 2. If none is found, generic interface class drivers can attach.
SEE ALSOThe USB specifications can be found at: http://www.usb.org/developers/docs/ libusb(3), usbdi(4), aue(4), axe(4), axge(4), cue(4), ehci(4), kue(4), mos(4), ohci(4), pci(4), rue(4), ucom(4), udav(4), uhci(4), uhid(4), ukbd(4), ulpt(4), umass(4), ums(4), uplcom(4), urio(4), uvscom(4), usbconfig(8), xhci(4)
STANDARDSThe usb module complies with the USB 2.0 standard.
BSD November 26, 2013 BSD
HISTORYThe usb module has been inspired by the NetBSD USB stack initially written by Lennart Augustsson. The usb module was written by Hans Petter Selasky <@FreeBSD.org>.
|This manual||Reference||Other manuals|
atp(4freebsd) | cdce(4freebsd) | ehci(4freebsd) | if_cdce(4freebsd) | if_rum(4freebsd) | if_run(4freebsd) | if_uath(4freebsd) | if_udav(4freebsd) | if_upgt(4freebsd) | if_ural(4freebsd) | if_urndis(4freebsd) | if_urtw(4freebsd) | if_zyd(4freebsd) | ng_ubt(4freebsd) | rsu(4freebsd) | rum(4freebsd) | run(4freebsd) | snd_uaudio(4freebsd) | u3g(4freebsd) | u3gstub(4freebsd)
aue(4freebsd) | axe(4freebsd) | axge(4freebsd) | cue(4freebsd) | ehci(4freebsd) | kue(4freebsd) | mos(4freebsd) | ohci(4freebsd) | pci(4freebsd) | rue(4freebsd) | ucom(4freebsd) | udav(4freebsd) | uhci(4freebsd) | uhid(4freebsd) | ukbd(4freebsd) | ulpt(4freebsd) | umass(4freebsd) | ums(4freebsd) | uplcom(4freebsd) | urio(4freebsd)